Changing the traction for SG

[Ben MN Support]

Hello,

Just recently I have had a few questions regarding changing the traction for the SizeGenetics.

Below I have put together some basic traction change guidelines to help you all out!

Changing traction force

When the device has been fitted the force of traction can be adjusted by turning the two thumb-screws in either a clockwise direction (for increasing traction) or an anti clockwise direction (to loosen traction force)

The actual force exerted can be read on the hexagonal pistons and the force of traction can be varied from 600 to 900, 1200 or 1500g

Each marking on the piston equals a traction force of 300g. Thus, at the exertion of maximum force (1500g) only one marking is visible on the piston;

*The mark closest to top of the device (nearest the penis head) = 900g
*The mark in the middle = 1200g
*The mark closest to the bottom of the device (nearest the base of the penis) = 1500g
*You should not be able to see the threads at any time and if they are visible, a new extension piece needs to be added

I would advise that the hexagonal bars leading up to the spring loaded cylinder must be stationary, and not twist when you turn the thumb screws, as this will not allow the traction force to be changed.

I would also advise that the penis must be held securely in place to allow the arms to creep into the cylinder and therefore alter the traction force.

I hope that this information is helpful.

Any questions, give me a shout!

Regards,

Ben.
MaleExtra™ Male Enhancement Pill - 15% discount for all Mens-Network members!
To order your first batch of MaleExtra pills, go to www.maleextra.com (http://www.maleextra.com)
and get a 15% discount when you use discount code MN15

[anth1225]

Hope you don't mind Ben but I made this a Sticky so people can easily find it.

anth

[Ben MN Support]

That's cool with me anth!

I would rather people could find the link easily so cheers for doing that.

On another note, if anyone has any additional questions regarding changing the traction force for the SizeGenetics, please fire any questions in my direction and I will be happy to assist you further.

Regards,

Ben.
MaleExtra™ Male Enhancement Pill - 15% discount for all Mens-Network members!
To order your first batch of MaleExtra pills, go to www.maleextra.com (http://www.maleextra.com)
and get a 15% discount when you use discount code MN15

[zilla]

Traction question: I've read many threads and called several times. No one can explain the following to me:

"How does retracting create tension"

How is it physically possible to increase tension (and stress on the peins) with the metal rods when unscrewing the metal threads that are supposed to retract into the 2 plastic tubes at end of the device near the head of the penis?

I can do this manually by pushing back the plastic tip back towards my body (manually retracting) but then THERE IS NO TENSION!!!!

When I add metal rods and or unscrew the threads; that is when I create the tension. The plastic tip does not retract. AND IF IT DID RETRACT IT WOULD ELIMINATE THE TENSION.

Please explain. Want to make sure I'm not hurting myself.

BTW I am very happy with device. Using for 13 weeks and added extender rods 2 times already. Increases in girth and somewhat in length. Mostly impressed with added sensation during sex.

ty

[Ben MN Support]

Hello,

I am sorry to hear that you are experiencing difficulties with the traction.

I am happy to assist you with your device, to enable you to correctly change the traction force.

You should not attempt to change the traction on your device until you have been wearing the device for at least six weeks.

When the device has been fitted correctly the force of traction can be adjusted by turning the two thumb-screws in either a clockwise direction (for increasing traction) or an anti clockwise direction (to loosen traction force)

In order to change the traction successfully you must ensure the following:

* You must be wearing the device when you attempt to change the traction

* The device must be set to the correct length - roughly one centimetre longer than your fully outstretched penis

* Your flaccid penis must be fully outstretched whilst the device is in use

* The strap must be secured tightly to hold the penis in place to allow the arms of the device to creep into the cylinder

The actual force exerted can be read on the hexagonal pistons and the force of traction can be varied from 600 to 900, 1200 or 1500g

The device will automatically exert a force of traction of 600g when the device is in use.

Each marking on the piston equals a traction force of 300g. Thus, at the exertion of maximum force (1500g) only one marking is visible on the piston;

*The mark closest to top of the device (nearest the penis head) = 900g
*The mark in the middle = 1200g
*The mark closest to the bottom of the device (nearest the base of the penis) = 1500g
*You should not be able to see the threads at any time – and if they are visible, a new extension piece needs to be added

I hope this information is helpful.

If you have any further questions do not hesitate to contact me.

Regards

[bnbstrategies]

What happens if you get an erection while wearing the devise? and you have a curve?
Can this cause pain/injury?

[Ben MN Support]

Hello,

Thank you for your enquiry.

I can advise that if you get an erection whilst wearing the device you will need to remove it.

This is until the erection has gone once the erection has gone you can then reapply the device.

If you do have a curve the device will not be uncomfortable to wear.

When you first start wearing the device you may feel a slight stretch this however will not be uncomfortable

Regards

Ben

[zilla]

Great. TY for reply. So it appears my device is broken.
When I unscrew extender rods they just push out the white plastic tip. The white plastic tip does NOT retract to the next traction force (600g to 900g). Device just stays on 600g BUT I do continue to add extender rods and continue to stretch the penis this way with good results.

Am I wasting time, going to hurt myself, etc...

Any chance your company can create a video with a live human model showing the white plastic tip retracting???? This would be very helpful.

TY.



Hello,

I am sorry to hear that you are experiencing difficulties with the traction.

I am happy to assist you with your device, to enable you to correctly change the traction force.

You should not attempt to change the traction on your device until you have been wearing the device for at least six weeks.

When the device has been fitted correctly the force of traction can be adjusted by turning the two thumb-screws in either a clockwise direction (for increasing traction) or an anti clockwise direction (to loosen traction force)

In order to change the traction successfully you must ensure the following:

* You must be wearing the device when you attempt to change the traction

* The device must be set to the correct length - roughly one centimetre longer than your fully outstretched penis

* Your flaccid penis must be fully outstretched whilst the device is in use

* The strap must be secured tightly to hold the penis in place to allow the arms of the device to creep into the cylinder

The actual force exerted can be read on the hexagonal pistons and the force of traction can be varied from 600 to 900, 1200 or 1500g

The device will automatically exert a force of traction of 600g when the device is in use.

Each marking on the piston equals a traction force of 300g. Thus, at the exertion of maximum force (1500g) only one marking is visible on the piston;

*The mark closest to top of the device (nearest the penis head) = 900g
*The mark in the middle = 1200g
*The mark closest to the bottom of the device (nearest the base of the penis) = 1500g
*You should not be able to see the threads at any time – and if they are visible, a new extension piece needs to be added

I hope this information is helpful.

If you have any further questions do not hesitate to contact me.

Regards

[Miamihurricane]

I'm 3 weeks in and I don't need the traction until I believe the sixth week ,but the traction doesn't seem to work either. If I turn the rods eventually they will fall off. All three lines remain visible. When I turn the rods the extender does extend but all the lines are visible so I never know what the traction is. And also when using the extender you are suppose to stretch the penis as far as you can then place the extender? Or just pull it slighty then place it? Btw I love it ,already I see a difference,I want to stick with it. I have combined the male extra,extender and pe exercises. Please help!! Thanks

[chinchillables]

I'm 3 weeks in and I don't need the traction until I believe the sixth week ,but the traction doesn't seem to work either. If I turn the rods eventually they will fall off. All three lines remain visible. When I turn the rods the extender does extend but all the lines are visible so I never know what the traction is. And also when using the extender you are suppose to stretch the penis as far as you can then place the extender?http://imageshackz.com/images/mextra.gifOr just pull it slighty then place it? Btw I love it ,already I see a difference,I want to stick with it. I have combined the male extra,extender and pe exercises.Please help!! Thanks

That's the best way to go, combining multiple aids for maximal results. As for the traction thing... I had found a video on another site a few days back that explained the rods and showed detail of how to adjust them properly, etc. I'll see if I can find it and come back and post it or pm it to you or something.

[Miamihurricane]

That's the best way to go, combining multiple aids for maximal results. As for the traction thing... I had found a video on another site a few days back that explained the rods and showed detail of how to adjust them properly, etc. I'll see if I can find it and come back and post it or pm it to you or something.

Yea, please, I don't know if I'm doing it right,I followed the instructions but I'm not sure

[Daz MN Support]

Hello

maybe you could post the thread on the forum so other users can use the video too :banana:

Regards

[rastaman]

I'm 3 weeks in and I don't need the traction until I believe the sixth week ,but the traction doesn't seem to work either. If I turn the rods eventually they will fall off. All three lines remain visible. When I turn the rods the extender does extend but all the lines are visible so I never know what the traction is. And also when using the extender you are suppose to stretch the penis as far as you can then place the extender? Or just pull it slighty then place it? Btw I love it ,already I see a difference,I want to stick with it. I have combined the male extra,extender and pe exercises. Please help!! Thanks

I am having the same issue. Have you figured this out as yet? Will be great if we had a proper video to explain it. I have just started and Im not sure if I am doing it right. Pls help me out if you have figured it.

TY

[Daz MN Support]

Hello,

Im sorry to hear that you are experiencing difficulties.

I would recommend that you contact the customer support team directly.

They should be able to assist you further.

The contact telephone numbers are as follows:

0115 979 8446 UK
1800 209 1670 US

Regards

[bandolier]

For those of you having problems you may want to try this. after adding the extensions and tightening them with the supplied "coin" tools, put the white plastic tip on the end of the rods and push down HARD! I do this by holding the rods in my closed hands...one in each hand...and using my thumbs to push down HARD on the rounded tips of the plastic end piece. This "seats" the plastic end piece onto each rod firmly and securely. I hope this helps!
bpt

[rastaman]

Hi bandolier,

thanks for your reply. I will give it a try. so how long have u been using sg and how is your progress?

[bandolier]

hi rastaman,
I will be starting my 11th week on Monday. I have noticed some serious girth and length changes while flacid:) My girth during erection has also increased but have not noticed any difference in length during erection. Seems like most of the serious changes take 4 months or so. No prob...I'm in it for the long haul:)
bpt

[rastaman]

Bandolier,

If you dont mind me asking..How much have you increased in erect length and girth so far? Also when you first started using the system how lond did it take you to add more rods? I have just started my first week and I have already added a 2cm rod. How many cms in rod length did you add in your first 6 weeks?

[bandolier]

rastaman,

I really have not gained any erect length but have added noticable erect girth. unfortunetly I did not measure my starting flacid or erect girth. No doubt I am seeing the most gains in flacid girth and flacid length. I added my first "short" rod within a week as well. By the forth week or so I switched out the "short" rod for the "medium" rod. Around the sixth week I was using the "short" and "medium" rods together but found myself slipping out of the device if I moved around to much. I have sense gone back to just using the "medium" rod and trying to increase the amount of tension. This of course is with a "long" rod attatched the whole time:)
bpt

[rastaman]

Bandolier,

Thank you for your replies. Its always good to hear other peoples progress using this device.

[bandolier]

rastaman,
No problem. Hope this info helps. I was really checking out the site to buy replacement parts and came across the forum section. My advice is to buy extra comfort strips and foam rings. These are the two pieces which connect to the top plastic piece and hold you in place. The rubber comfort strip is getting stripped under the constant pressure and the foam ring is getting tore up too!! I decided to buy more now so I would not have any interuption. Nice talking to you and hope all goes well:)
bpt

[Daz MN Support]

Hello,

That sounds like a good idea Its always good to have spares so if your straps does break you can carry on using the device and not have to wait for a delivery on new straps :spin:

[suckaaa]

I get the traction to work when my penis is extended straight,
but when I move it pointing down it moves back up and all the lines show again.

What am I doing wrong? is it better to where it straight to get traction?

[Daz MN Support]

Hi,

Have you got the device set to 1cm longer than your fully outstretched penis?

Because if you have the device set to the correct length the traction shouldn't change if you have it pointing down or straight out.

Also when you change the traction are you use the hexagonal bars or the thumb screws? I'd recommend the bars as this make the traction easier to change.

Regards

Darren