SG instructions

[Ben MN Support]

Hello everyone,

Recently I have had a few questions regarding how to use the SizeGenetics device.

I can confirm that there is an instructional DVD ROM with every purchase which demonstrates how the device should be worn.

The DVD is behind the foam lining in the top of the case.

Below are some basic instructions of how to use the device though to get you started:

Assembly

1. The device should be set at a size which is just over your flaccid length (additional pieces can be added by using the keys provided)

2. There is a basal plastic ring (Piece 1) with a recess for the urethra (Piece 2 - same as Piece 1). The ring is fastened around the base of the penis.

3. Two metal bars, one with a right-handed thread (Piece 3), the other with a left-handed thread (Piece 4) are attached to the basal ring. Hidden inside each bar, is a spring contrivance (Piece 5).

4. At the distal end the two bars are attached to a plastic support (Piece 6) with two holes, for the comfort strap (Piece 7) to fit through.

5. The components 1-5 are pre assembled on delivery

Usage

1.The device is mounted by fastening the basal ring (Piece 1) around the base of the penis, so that the two metal bars (Pieces 3+4) run parallel with the penis, one on each side, and the head of the penis rests in the bowl-shaped support (Piece 6).

2.By passing the two ends of the comfort strap (Piece 7) through the holes in the plastic support (Piece 6) a loop is made through which the head of the penis is introduced. Before fastening of the penis the plastic support should be pressed towards the body so that the two springs press home.

3.The comfort strap is fastened around the penis head by pulling the ends of the comfort strap (Piece 7) through the reverse side of the support. If you have not been circumcised the strap is fitted just below the glans with the foreskin in place.

4.Additional pieces of metal bar (Pieces 8, 9 + 10) may be added as required by means of the two keys (Piece 11).

Additional bars come in three sizes:
1 cm (small) (Piece 8)
2 cm (medium) (Piece 9)
4 cm (large) (Piece 10)

I hope that this information has been helpful.

If anyone has any additional questions just give me a shout.

Kind regards,

Ben.
MaleExtra™ Male Enhancement Pill - 15% discount for all Mens-Network members!
To order your first batch of MaleExtra pills, go to www.maleextra.com
and get a 15% discount when you use discount code MN15

[Ben MN Support]

Further to this, if you have any additional questions just send me a PM and I will be happy to help.

Regards,

[chinchillables]

Originally Posted by Ben MN Support

Further to this, if you have any additional questions just send me a PM and I will be happy to help.

Regards,

How long will that discount code in your signature be valid?

[Ben MN Support]

Hello,

The $50 discount code will work for as long as it is in my signature!

It currently does not have an expiry date. However, the company can pull this promotion at any time.

I hope this helps

Cheers,

[kenji51590]

Hello, wondering about how the head should look like when i strap it in.. after 20+ min or so I'll loose some blood from the penis and the head shrivels a bit. Wondering if I have it too tight or maybe it's too long. I don't feel any pain just the head looks a bit shriveled.

[Ben MN Support]

The head of the penis should be securely fastened into the device but at the same time you do not want to cut off blood circulation.

What I suggest is you perform the warm up PE exercises before wearing the device and this should help.

Also, remember to remove the device once every 2 hours and massage the penis for 7-10 mins to help restore blood flow.

[lonewolf101]

right I unscrewed the pre-assembled bits (dont ask why, was just fiddling about). I have not damaged anything. Im trying to screw the pre-assembled parts back in, but they seem impossible to screw back in, its so hard!!!! Is there a reason for this & any tips?

[Pharma99]

Originally Posted by chinchillables

How long will that discount code in your signature be valid?

Thanks much for the share in regards to the discount code.

[Ben MN Support]

Originally Posted by lonewolf101

right I unscrewed the pre-assembled bits (dont ask why, was just fiddling about). I have not damaged anything. Im trying to screw the pre-assembled parts back in, but they seem impossible to screw back in, its so hard!!!! Is there a reason for this & any tips?

Ever heard the expression curiosity killed the cat!

It is very difficult to screw the parts back in and this is why they are sent pre-assembled...

If you are still struggling, I would suggest you email customer support:

support@sizegenetics.com

Cheers,

[Ben MN Support]

Originally Posted by Pharma99

Thanks much for the share in regards to the discount code.

Your welcome

[NovaPat1970]

How many hours a day do you need to wear the device to see results?

[Daz MN Support]

Hello

It depends on how long you have had the device for.

When you first receive it you should wear it for a few hours per day.

You should then increase this by 1 hour each week until you are wearing it for 8 hours per day.

If you have any more in-depth questions I would recommend that you contact the SizeGenetics Customer support team directly.

Regards